Replacing uPVC Window Handles
It is easy to change the handles on windows made of upvc. It is important to make sure that the new handle is a good fit for the spindle cut out in the window mechanism.
If the steps below are followed properly the cockspur handle will fit most windows. The key is the step height of the handle.
What to Do You Look For?
Over time, uPVC handles on many windows in the UK begin to show signs wear and wear and tear. The window handle can become loose or difficult-to-operate when this occurs. Anyone who is familiar working with basic hand tools can accomplish this fairly simple task.
The first step is to ensure that the handle is securely attached to the frame of the window and in the open position. The next step is to find the screws or pins which hold the handle in place. These are usually located on the inside of the handle. They can be removed using a screwdriver and pliers.
Once the handle is loose, it can be removed from its hinges by gently pulling off. The next step is to find a replacement handle that is the same design and size. upvc door handles can be done in the DIY store or on the internet. The process should take only five minutes, and you will need a screwdriver.
When replacing the handle on a uPVC handle, it is important to consider the step height. This is the distance between the handle's base and where it is placed in the frame of the window. This is typically an average measurement, but it is important to check the step height of your existing handle prior to ordering a new one.
There are several sizes depending on the kind of handle. Inline handles can be found for uPVC windows that have lug centres of 31mm while cockspur handles have lug centres of 43mm. Tilt-and turn handles are typically found on uPVC windows. They have a specific design which allows the window be tilted for ventilation and then rotated to fully open the window.
The most common breakage in uPVC handles is that they crack inside rather than breaking off from the base section. This can make them hard to open and therefore it is essential to ensure that the replacement handle you purchase has the same length of spindle that your current one.
Remove the handle that was previously used
If your window handles are damaged or not properly installed, they could cause double-glazed windows to open and close incorrectly. They may even get stuck. This could be due to many factors, such as general wear and tear on the metal handle or corrosion. In these instances, it is important to seek replacement upvc window handles as soon as you can in order to avoid further damage and loss of functionality.
When replacing the handles of windows made of upvc it is recommended to remove the old handles from the window. To do this, start by taking off the screw that is covered when the handle is in the closed position. Once you have removed the screw, you can remove the handle. It is recommended to use an electric screwdriver for this, as it makes the task easier and quicker.
It is also important to be aware that screws could be hidden in caps made of plastic. It is best to remove the covers using a Stanley knife. After you have removed the old handle, you will be required to inspect the square cutout on the base to make sure that the new handle you choose for the window lock is compatible. This is important as you'll need to measure the length of the spindle of the old handle to ensure that it is the same size as the window mechanism and the handle spindle that has been cut out.
There are three types of upvc handles: Espag handles with a central screw that can be turned either left or right and Cranked handles with two screws and Spade handles, which have arms that are flat and can be used either side of the upvc window. Once you have a suitable replacement, it is just a matter of screwing the handle in place and making sure that the spindle is correctly inserted into the lock mechanism. After you have done this then tighten the handle to the window frame. The new upvc handles will now be secured.
Measure the Spindle
If you have to replace a upvc handle that has fallen, it's likely the spindle holding it in place is damaged or is loose. In some instances, this could be fixed with a screw or pin to tighten it. In some instances it might be necessary to replace the handle. There are many types of upvc window handles. There are three types of handles: inline espagnolette, tilt-and-turn, and cockspur. Each handle type has its own procedure for installing and removing the handle.
It is crucial to measure the handle before buying a replacement. This will help ensure that the new handle is the right size and fits within the window. All handles are calibrated in accordance with industry standards, so it is easy to determine the right size.
To measure the size of your handle, first remove it from the window by turning it to the open position. You should be able to determine the size of the screw or pin that holds the handle. Then you can use a tape measure or ruler to determine the length of the spindle. Once you know the length of your spindle it is possible to buy a replacement of the exact same length.
When buying a replacement you should be aware of the step height of the upvc window handle. The step height is measured from the base to the point at which the handle is positioned on the frame. Typically, this will be about 21mm for uPVC windows and 9mm for aluminum. To be sure that the new handle will work, you can drop something into the gap to see how far it goes before it comes into contact with an obstruction.
Cockspur handles typically have different backset heights depending on the style of window they're installed in. Inline the espag handle heights range from 43mm from centre to centre (two fixing points). Cockspur handles have different backsets depending on which window design they are placed in. This is due to the fact that they have a spur which extends from the handle and locks onto a cockspur wedge hitting plate.
Fit the New Handle
After you have chosen the new handle, make sure it is aligned with the holes for screws on the door. Then, secure it with the screws provided. If you're replacing the latch lever, it can be installed the same way as the main door handle. After that, attach the door trim again to hide the mounting screws.
Tips: To remove the metal head from a wooden wedge, place the handle on the floor so that its wide end is on the ground. Then, you can use to tap the thin end. Be careful not damage the handle or spindle.